RSPAN on N1548P
Hello,I've recently purchased 3 N1548P. Each one distributed at different floors and interconnect with fiber connection.Let's say:- 1/F: N1548P (1/0/1 connected to IP-PBX; 1/0/2 connected to SPAN...
View Articleis my X1052P switch bricked?
Hi,I just unboxed my new Dell X1052P switch. I got into the GUI and first updated the boot code to 1.00.17 rebooted the switch and it was happy. It came right up. Then I loaded firmware 3.00.70 and...
View ArticleDell Networking N-Series DNOS 6.3.0.9 required process before upgade.
Last week DNOS 6.3.0.9 was released for the N-series switches. I know everyone reads release notes thoroughly..... But I wanted to raise some awareness to a specific requirement for this...
View ArticleLAG between VRTX 10Gb switch and X-series
Hi there,I am trying to configure a LAG between a VRTX 10Gb switch and an X-series switch (using Dell 10Gb SFP+ cables) - I have tried both X4012 and X1052 but I have the same issue.When 1 of the 2...
View ArticleRSTP behavior when two S3048-ON configured with VLT and RSTP connected with...
HiI have two S3048-ON configured with VLT and RSTP. I have connected one PowerConnect 5548 to each S3048-ON (1 cable to each, no LACP). The 5548 also have RSTP enabled with a priority of 57344.One...
View ArticlePower connect 5548 won't boot and not cli access.
We have two Powerconnect 5548 used to distribute AV through the office we started to set up the second 5548 and were able to access the cli a couple times after that we have not been able to access the...
View ArticleIs the spanning-tree bpdu filtering on the 5548 the same as "spanning-tree...
It looks to me like the "spanning-tree bpdu filtering" on the 5548 the same as "spanning-tree portfast bpdufilter default" on the N series switches -- is that correct? If not what is the equivalent...
View ArticleDell N3000 Series LLDP neighbor ID
The N3024, lldp sends the "system ID" or "neighbor ID" as the mac of the switch to my other lldp enabled devices. Or at least that is what is received. Can I specify what is sent as the lldp ID or...
View Articlepowerconnect 8024F and 5524 operating at 100Mbps
We have a situation where it appears that all traffic communicating over our 8024F and 5524 switches is transferring at 100Mbps.I'm not a networking guy and we outsource our networking to consultants...
View ArticleClik here to view.
MLAG N4000 issue
I have 2 stacks of two N4032F (interstack 4x10GE) connected with 4x10GE, mesheh, on to one switch.Stacks are connected by LACP mode active. This is CoreSome Cisco switches are connected to stack of...
View ArticleClik here to view.
N4000 interstack LACP communicatins issue
I have 2 stacks N4032F (interstack links 4x10GE) connected by 4x10GE LACP mode active. This is core. Some Cisco switches are connected to them on LACP 2x10GEI can not ping some hosts from one side to...
View ArticleConfiguration for MXL 10/40 & Dell N4032
Hi All,I am new on Blade Server, Can any body help me to configure the MXL 10/40 Blade switch with N4032.I am able to create stack between two MXL 10/40 & two N4032. But i am not able to find the...
View ArticleChange MTU to lag members
Hello,I need change the MTU to lag members, Can we have a little cut in the VLT when we change the configuration?The order in the change is important? first the physical ports and next the...
View ArticleHelp connect Cisco4510r+e and Dell PowerEdge M1000e by 10GB
At the Cisco4510r+e connection (WS-X4712-SFP+E card) the SFP-H10GB-CU5M and Dell PowerEdge M1000e cable (Powerconect m8024 card) there is no linkAt the Cisco4510r+e connection (WS-X4712-SFP+E card) of...
View Articleswitch fabric capacity
Hi everyoneAccording to the spec sheet, the dell S3048-ON switch fabric capacity is 260Gbps, how to caculate the switch fabric? S3048-ON has 48 GbE and 4 SFP+. Can someone answer the question?cheers.
View ArticleX-Series DHCP Server settings only allow one DNS server?!
Successfully set up our new X4012 switch, including the DHCP server options so that it gives out IP addresses to devices, except for one issue: Under Network Administration --> DHCP Server -->...
View ArticleN4000 Leaking traffic
After upgrading our N4032F stack to DNOS 6.3.0.9 I noticed some strange traffic hitting our firewall. Traffic from 2 devices on the same L2 network on a vlan that is not routable seems to be hitting...
View ArticleIO Module
is it possible to add PCIe 10 GigabitEthernet to IOM management? to manipulate and configure switchport?
View ArticlePower connect 8024 VLT support?
Hi, I'm connecting a Cisco UCS to Dell PC 8024 switches. Cisco recommend vPC (virtual port channel) or VLT (Virtual LAN Trunk) for connectivity. Does the Dell PC8024 support VLT? If so, has anyone...
View ArticlePort MAC addresses Dell 6224 Switch
Is there any command to find out the ports MAC addresses of a 6224 switch?! I'm desperately looking for it since yesterday... Thanks in advance!
View Article