S4810 rebooted itself
Hello,Can someone help me to check why S4810 switch rebooted itself? Before rebooting I fond the logs:critical local7 %STKUNIT0-M:CP %CHMGR-2-STACKUNIT_DOWN: Major alarm: Stack unit 0 down - IPC...
View Articleunmanagement mode on 2824
Hi all,i'am trying to switch from unmanagement to management mode on a 2824 but It dosen't work.I pressed the button mode on the front panel for more than 7 seconds, then the switch has rebooted....
View Article6248 Buffer Log: Need help understanding some log entries
Hello,got some error messages, can someone tell me what's going wrong?19 Notice JAN 06 07:20:59 TRAPMGR Link Up: 2/0/5220Info JAN 06 07:21:02UNKN USL: error setting trunk 6 info, hwRv -11 dbRv...
View ArticleResetting a Powerconnect 5424 to factory defaults without the use of the...
Good day, I recently purchased a Powerconnect 5424 the switch was not reset before shipping. I am able to access the webGUI login screen. And the switch functions great I just can't access the...
View ArticleClik here to view.
MLAG + VTLi + STP No traffic
Hello, I have this topologyCan not get working VTLi and MLAG togheter.Try to we working only up conectivity between X1052 and N4032F's but there is no traffic allowed.I suspect maybe is a spanning tree...
View ArticleSyslog formatting Question
We have several dell power connect switches on our network and I have a question about how to change the syslog formatting.Our syslog server sorts our messages based on the hostaname portion of the...
View ArticleDell DFM 1815dn
My Windows 7 computer no longer recognizes my printer. I have tried repeatedly to update the driver with no luck. It doesn't even recognize it as a printer.
View ArticleFrameproblem
Hi, I connected two racks in different locations with a N1524 and a 5424.On both are 3 vlans configured (2,10,250).The ports on both switches are in trunk mode tagged with the 3 vlans 2,10,250.On the...
View ArticleHow to convert Hundred Gig port on DellZ9100-ON switch to default...
Hi ,I am trying to split Hundred Gig port to quad port running at 25G speed.When I issue the command "stack-unit 1 port 29 portmode quad speed 25G" it displays an error message "% Error: Quad mode...
View ArticlePort security 6248
Hi,I have a phone and a PC plugged into a switch port I'm trying to configure port security on. I've enabled port security with:switch(config-if-3/g43)#port security max 2switch(config-if-3/g43)#port...
View ArticleWhat am i am missing with rip
How can I disable on the new firmware on the n3024? I have it disabled, but it still shows rip router in show run. I am setting up of now. The GUI and command line show it disabled.
View ArticleReset Password on DELL Switch N3024
Hi All,Actually I forget the username/password on my DELL N3024 Switch.How to reset the username/password but still have the switch configuration?Please kindly need your help.
View ArticlePowerConnect 7048 no enable password issue
Hi,I'm facing an issue with PowerConnect 7048.I'm trying to add it in my rancid, so, i would like to disable the enable password, i tried the following:conf tusername "rancid" password...
View ArticleAdvantage of PowerConnect Switches with Dell Servers
Basic question, I need to get a switch to manage a few previous generation Dell PowerEdge servers. What if any are the advantages of staying with the same vendor and using a Dell PowerEdge switch...
View ArticleDHCP packet issues on N2/3/4000 switches
Information post rather than a question/ problem.We had suffered for some time with poor DHCP service at remote site when we lose Internet connection to our main site and all traffic fails over to the...
View ArticlePowerConnect 2848 - Creating VLANS for other organization in the same office
Hi,I need to separate two VLANS so that the two organisation would not have access to each other computer and files, but still able to share the internet access. How should I setup using the...
View ArticleClik here to view.
Setting VLAN via SNMP on Dell Network N1548
I'm back after six years, with the same issue but now on a new switch... I bought 60 of these switches under the premise that they worked the same as the old PowerConnect 5548 and while they seem to do...
View ArticleClik here to view.
8204F port errors
We are getting FCS and Internal MAC Rx errors on a single port. I have replaced the SFP and fibre cable as well as moving the cable to an alternate port, none of which has stopped the errors which...
View ArticlePowerConnect 2824 configuration access issues
I have a Dell PC2824 managed switch.When first powered up, it runs in unmanaged mode, though the fan and manage mode lights blink as if it's trying to configure itself.With a telnet app, connected to a...
View ArticleMac based ACE blocking DHCP traffic? (PowerConnect 5548)
Hi all,we have a PowerConnect 5548 switch here that is only used for IP phones.To be sure that no other device works at a port of the switch a mac based ACL was created.It is applied to port gi1/0/1...
View Article