Rate limiting on Dell N2048 Switch
Based on the user guide, ACLs can provide ingress traffic rate limiting, while egress ACLs support traffic shaping. When I do:# ip access-list test # permit every rate-limit 500000 128# exit# interface...
View ArticleN3048 VLANs connected to non Dell switches?
Firstly, thanks for reading.I'm doing some test configuration to move our network away from a flat network to one that uses VLANs. I've got a N3048 setup with a test DHCP server and I've created two...
View Articlem1000e - Dell Ethernet pass-through
hello,Could you say me how can I configure a vlan on this switch?I don't find any informations or documentations about this subject.I tried via the ikvm, via the console management and the Chassis...
View ArticlePowerConnect 8100: loop_protect_txrx.c(164)
Hello!I am receiving the message in log:<191> Dec 23 14:08:43 dell-abk1-208-1-1 LOOP_PROT[dtlTask]: loop_protect_txrx.c(164) 26796 %% Is looped probably, since feature not enabled discarding the...
View ArticleLost newbie: My switch won't switch, M6220.
Hi,I'm new to Dell's products. I just bough a used M1000e with M610 blades to train on but I'm having a heck of a time getting the M6220 switches to do anything. I have six M6620 switches, two of them...
View ArticleLeap second for ST4048T
Hello team,I use ST4048T for service.Is there any known issue of leap second with NTP.Let me know any imformation of this, if you can support.Best regards,
View Articleforce10 s4810 use VLAN 1
I have one of these switches. We are going to replace the main core switch with this model. We have the VLAN 1 as the servers VLAN. We want to use the same VLAN for servers in this switch. But we cant...
View ArticleForce10 S4810
Does anyone know how to get updates for the IOS (Dell Application Software) for force10 S4810 switches? When I go to support center and enter my service tag I do not get any options to download the...
View ArticleHow to show the running config on a Dell 6248 without line breaks.
Is there a way we can get the running config without the 'more' or 'quit' prompt. ?
View ArticleS4810 how to start configuring
Hello,I've been handed a s4810 as a test device but i have no clue on how to configure this.I have connection to the cli, can execute and read some settings but i'm far out of my comfort zone.I've read...
View ArticleN3000 series stack issues
I have 7 N3000 switches in a stack.There is 1 N3048 and 1 N3024 These to are number 6 and 7 and they are where all my servers get plugged in to.The other 5 switches are N3048p where all clients get...
View ArticleHow do you Port Rate a single Port on N1548?
Hey guys,We have recently set up some Dell N1548s and we would like to learn how to limit a port to a desired throughput/bandwidth.For Example:We will have a 250x250 fiber connection straight into this...
View Articlestacking question for N2048
hi there,Looking at the spec sheet for N2000 switches I notice that for stacking it says:"2 rear stacking ports (21Gbps) supporting up to 84Gbps (fullduplex)"Just to clarify if I connect 2x N2048P with...
View ArticleClik here to view.
Powerconnect 8132F Firmware Backup Issue
Hi all,While preparing to update the firmware on my two recently aquired 8132F's to version 6.3 I thought I would backup my know good active version as a precaution. On switch #1 this all went fine,...
View ArticleVlan Layer 3 x Layer 2
Good afternoon I have some switchs in my park and I have a vlan project to create, but I have some doubts about what would be the best strategy to do to make this process. Ok let's go I currently have...
View ArticleNetwork dropouts when disconnecting Stack UpLink Ports ( SDM template )
Hi guysI've got 3 Powerconnect 8024f's in a stacked setup, using just a simple loop stack where one swtich plugs into the other using 1 port each.. (each swtich has 2 stacking ports, one going to each...
View ArticleClik here to view.
OMNM v6.2 and S4048-ON resync problem
Hi,when I try to discover our s4048-on these error and warning always appear:Could you please give me a advice what's wrong? Or how should I configure the switch and OMNM.We are running OMNM v6.2...
View ArticleDell S4810 critical syslog
Hi there,I need the help of someone who ever faced an out-of-nowhere reload of S4810 due to the following syslog messages.1. %STKUNIT0-M:CP %CHMGR-2-STACKUNIT_DOWN: Major alarm: Stack unit 0 down - IPC...
View ArticleDELL Z9100 IPV6
Hi guys,Anyone worked with the Z9100 yet?Besides the fact i`m facing some issues when trying to establish IPV6 BGP sessions ( Optional attribute error ), even though same setup is working for 20 peers,...
View ArticleNo routing between VLANs on N3048
Hi,I'm new on DELL switches so I becoming quite crazy understanding why routing is not working between VLANS created on brand new DELL N3048.Hi have for now 3 VLAN: 1, 2 and 3On the default VLAN 1...
View Article