Open Manage Network Manager Top Interface Bandwidth
I have a 1GB link between 2 sites. On one side the link goes into a Force 10 (10GB port) and the other side goes into a 4032f 10GB port. The speed displays as 1GB in Open Manage which is correct.My...
View ArticleM6348 Firmware password
Hello, I upgraded the firmware on my M6348 switch following the "Upgrading PowerConnect Switches from Version 2.x.x.x or 3.x.x.x or 4.x.x.x or 5.x.x.x to 5.1.10.1 Firmware" guide. However after it...
View ArticleForce10 to Cisco
Not sure how much Force10 is talked about here but I figured i'd give this a shot.I have a couple Force10 4810P switches I want to connect to a set of stacked Cisco 3750s. I'm a complete novice on the...
View ArticlePowerConnect 2848 set Qos for Voip vlan
Hi, have a PowerConnect 2848 and have set up a vlan for my phones. not sure how to set the QoS for the phones vlan.
View ArticleClik here to view.
Dell N2000 series stacking
Hi,I have unit 4 units n2048p stacking together as shown, can I force switch 1 become permanent master/management unit? Currently I only can renumber the unit ID. Firmware ver. 6.3.1.8Additional...
View ArticleVLANs can't see internet
Hello All, Â I am new to VLANs and trying to learn on my own. Â I have got a Powerconnect 6224. Â I setup two vlans and connected two machines to each VLAN. Â the machines in each VLAN can see each other...
View ArticleClik here to view.
Oversized package
HI Guys,i am facing an issue with a switch dell N1548, we have a separate network just for surveillance cameras and all our 160 ip cameras are distribuited in 7 switches of the the same model, all the...
View ArticleCopying configuration via SFTP on N-Series 3048P or 4032F
Testing (firmware 6.3.1.8)copy startup-config suser@host/.../filenameexecutes but always ends withFile transfer failed!But a check of destination host shows the file always transfers (I assume in its...
View ArticleX4012 - showing two default gateways?
OK, I have a pair of X4012 switches installed in a remote location. When I had configured them, I had originally set the default-gateway to an atypical value because I thought I was going to be sharing...
View Article40 port card throughput on E600 ExaScale chassis
Hi,Anyone using 40 port 10G cards (LC-EJ-10G-40S) with the E600i ExaScale platform ? What's the per port throughput on these cards ? Per docs each slot should have 100G of capacity but how does this...
View ArticleDell Enterprise Hardware & Software Updates, November 7-11
Popular Downloads Dell Server E-Support Tool (DSET) 3.7Dell Support Live Image (SLI) 2.2OpenManage Server Administrator (OMSA) 8.3OpenManage Essentials (OME) 2.2Servers & StorageBroadcom...
View ArticleOpen Manage Network Manager
I am using this software for switch management. For the past year, all I have got out of it is backing up the configs of all my switches. I knew that other cool stuff could be done with it and there is...
View ArticlePowerconnect 6248 and sonicwall router TZ300
I have a simple network for a retail shop. I am using a Sonicwall TZ300 router/firewall with a powerconnect 6248 switch. As well as a TP Link 8 port POE switch for my wifi nodes. The network suddenly...
View ArticleFailed to acquire an IP address on Vl1; DHCP Server did not respond.
N2024P keep loging this warning. How can I get rid off it. I do not use Vlan1 and switch management IP is on different Vlan which is VLAN100.
View ArticleIP configuration assistance on PowerConnect 6248
Hello everyone,I inherited a pair of stacked PC 6248 switches. These two switches are active and in production. I am not near these switches as there are located in another state at one of our other...
View ArticleNo lights on the ports m6220
HiI have a Dell m1000e chasis and a1/a2 has poweconnect m6220s. The internal ports 1-16 works and active. But when I plugged the cable on port 17-20 there is not light and show interfaces status says...
View ArticleQuestion about Switch N2048P ssh conection?
I need help with how to connect the switch through the ssh console to another switch. From a switch Dell N2048P to another from the console via ssh what is the way to do it only shows me the option of...
View ArticleChanging from /24 to /16 on a PowerConnect 5548p
Currently, the default VLAN on my switch is 10.1.1.0 /24. (it is currently the only VLAN)I want to change it to 10.1.0.0 /16. Is there a way to do this without resetting the config to defaults and...
View ArticleTrouble configuring a powerconnect 5548. No console
Hello,So I've inherit a powerconnect 5548P that I'm trying to setup but I can't get it to work.When I first plugged it I remember it was assigned an IP and I was able to reach the web interface. Now...
View ArticleNew MXL pair, one stack port flapping
We recently got a brand new M1000e with dual MXL switches in it, after cancelling the bare metal provisioning all I did was attempt to stack the two on the built in 40gb ports by using the "stack-unit...
View Article