Force10 MXL 10/40 in M1000e - DCBX issue.
I require the use of dcbx with my M1000e as I have an internal M4110s Equallogics, and am using an ESXi cluster to access it. This has not been a problem in the pas, but right now it is a real issue....
View Articlevery happy owner of dell s3048
Good day every one! I'm sorry for my english...i have SW-DELL#sh versionDell Real Time Operating System SoftwareDell Operating System Version: 2.0Dell Application Software Version: 9.10(0.1)Copyright...
View ArticleN3024
We have 2 vlans configured with 1 dhcp server configured for each vlan. Has been working fine for several months suddenly we are getting the message "No free IP address to offer in Pool (Pool Name).We...
View ArticleDell-M8428-k chassis - failover between fabric switch port A1 and A2 happens...
when We try to upgrade firmware of Fabric switch 1 (A1,B1, C1)...failover of network connections to other fabric switch 2 (A2, B2, C2) happens with a downtime, however SAN failover happens without any...
View ArticleX1026 switch VLAN problem
I have a few computers connected to the switch that are all able to talk to one another when they are not connected to a VLAN port. Once I connect a couple of the computers to VLAN ports they cannot...
View ArticleOOB Connectivity Error - VRTX Switch Modules R1-2401
Greetings, I am in the configuration process of the VRTX. The onboard R1-2401 has been given an OOB ip address of 10.10.10.8 with a default gw of 10.10.10.1. The VRTX switch is uplinked to a Cisco 3850...
View ArticleN2024P reports inline power being off
Hello,We have one N2024P that apparently fails to deliver power over PoE. I haven't tested the device myself but I have received reports that PoE device connected to any of the ports won't power up.If...
View ArticleDell equivalent of Configure Replace available?
Hi all,As title, was wondering if there was an equivalent of this very useful command set available to power connect switches? Along with an archive, that command allows an admin to roll back any...
View ArticleSet up ssh_key based access to MXL switches. Not "host based."
I've been reading the documentation, and cannot come up with a set of cohesive steps to follow in order to get simple key-based authentication to work,The docs separate this task into a wide variety of...
View ArticleMXL - how to get rid of the nag about Support Assist
Everytime I log in to my MXL stack I see this: The SupportAssist EULA acceptance option has not been selected. SupportAssist can be enabled once the SupportAssist EULA has been accepted. Use the:...
View ArticleMXL & NPAR
Hi Team,Our customer did setup the M630 with NPAR on BCM57840 card. Each M630 have 04 BMC57840 which gives him 8 partitions. But the "show mac-address-table" of MXL switch does not show all MAC of NPAR...
View ArticleHardware Warranty
Dell,We need some answers about a Dell PowerConnect 2824 switch that we purchased. At the time of purchase the Dell PowerConnect 2800 series had a lifetime hardware warranty. The switch recently...
View ArticleM8024-K port-channel to two Nexus 3000's - loop detected
Hi folks,looking to see if anyone else has had similar issues..We have implemented scenario 8 on page 14 of the...
View ArticleClik here to view.
spanning-tree portfast or switchport mode general
Hello I need to see if anyone can give me some help here. We have a VOIP system on our network. We would get drops every so often. Made changes to the firewall seemed to have fixed it. Now we recently...
View ArticleN3024 - finder is slow with 10Gbe
Hello,I miss something...I create 2 VLAN on my brand new N3024.In the second lan, i populate it with the module of the back with 2x 10Gbe and some 1Gbe in the front.I connected a NAS serveur with one...
View ArticleBrand New Dell 2808 Router Does not function.
1. The 2808 is not connected to the internet.2. When received, the 2808 powered up with the DHCP server disabled and port routing enabled. This is the default setting. Not good for normal use, but...
View ArticleClik here to view.
Dell PowerConnect 2848 uplink and management
Hi,We use 4 Dell PowerConnect 2848 switches for iDRAC traffic. This works perfectly.We use port 1 to 42 to connect to the servers, and 43 for the uplink. These ports are all in...
View ArticleClik here to view.
Configure MXL Blade switches for active paths using 2 qty CNA
Dear members,I need to configure a solution in which qty2 CNAs Qlogic 57810s are been used in LOM & port B of each m630 blade server, converged MXL switches placed in A1A2 & B1B2 slots. All the...
View ArticlePowerconnect 6248P quit forwarding traffic - MAC Pause Frames
Hello,We experienced a network outage the other day that prevented both our computers and phones from communicating. It seemed at first to be isolated to a single switch but seemed to spread. I was out...
View Article62xx - is routing between Vlans with interfaces in "Access mode" possible?
ideally between only chosen Vlans?many thanks.L.
View Article